Installing Windows XP On a SATA Hard Drive

Windows 2000 / XP Installation Basics

This guide will walk you through installing your operating system onto a new SATA [Serial ATA] hard drive in your computer. Please be sure to follow each step of the guide if you are running into issues getting your computer to identify or install onto your new SATA hard drive.

[NOTE: To install your operating system on a new SATA hard drive you are going to need to provide a SATA drivers disc during the Windows Setup process. This disc is NOT provided by the company you purchased your motherboard from. This is a disc you need to create using the makedisk.exe utility which can usually be found on your motherboard drivers disc or the manufacturers website. If you need more information on how to create this disc, please refer to the detailed instructions below. We will cover how to create an nVidia SATA or VIA SATA drivers disk depending on your chipset. This procedure can be different depending on the brand of motherboard you purchased.]

This guide is broken into the following sections which can be found below:

  1. HOW TOMAKE A SATA DRIVERS DISK          [FLOPPY DISK]
  2. nVidia Chipset SATA Drivers Disk
  3. VIA Chipset SATA Drivers Disk
  4. USING THE SATA DRIVERS DISK DURING THE WINDOWS INSTALLATION

How to Make a SATA Drivers Disk. [Floppy Disk] :

You will need to determine what chipset your motherboard is running before you proceed with this guide. This information should be listed on your motherboard box or in the manual that came with your motherboard. If you are unsure or do not have that information available you can check the model on the board itself [usually located near the PCI slots]. If it has an “N” in the model it is nVidia and if it has a “V” in the model it is a VIA chipset.

Now that you have determined what chipset you are running follow the instructions below for how to setup your SATA drivers disk for each chipset.

You will also need access to another system with Windows already installed so you can run your motherboard CD and create your drivers disk. If you do not have one at home you can ask to use a friend’s computer, or possibly use one from work.

[NOTE: Some motherboard disks now contain a button in the autorun menu for the makedisk utility. If this is included it will eliminate the need to manually find the correct program on your disk. In those cases I would recommend using that option and then referring to the instructions below if you have any further questions or need information about how to use the program itself.

NVIDIA CHIPSET INSTRUCTIONS: [VIA INSTRUCTIONS BELOW]

The first thing you will need to do to create your SATA drivers disc on a bootable floppy is setup a floppy disc to copy the drivers onto. This information can be found at the following link:

How to Format a Floppy Disc

Once your disc is ready and you want to create your SATA drivers disc you will need to take the Master CD that came with your motherboard and put it into your system.

Once you have the CD in your system go into Windows Explorer and navigate to where the Makedisk.exe utility is located on your disc. This can be done in one of two ways.

How to Find the MakeDisk Program. [Method #1]

The easiest way is to manually locate it on the disc since it will show you what folders you are in and will give you a better idea of what version of makedisk.exe you actually need to use.

For my example I will be using a motherboard disc from the ASUS A8N-SLI motherboard.

When the disk is in the CD-ROM it is titled “nForce4_Series“. Once I explore the disk it gives me several folders:

  1. BIN

  2. DRIVERS

  3. LINUXDRIVERS

  4. MANUAL

  5. SOFTWARE

In this case I am going to check in the “DRIVERS” folder as this is the most common place to start. Under the DRIVERS folder you have several options also:

  1. AMD

  2. AUDIO

  3. CHIPSET

  4. LAN

  5. SII3114

  6. USB

Now we will want to check in the “SII3114″ folder. [SII stands for Silicon Image, commonly associated with Serial ATA drives.] Once I click on this folder I see 4 folders and a “MakeDisk.exe” program.

  1. 64BIT

  2. DISK

  3. NOVELL

  4. RAID_DRIVER

  5. MakeDisk.exe

In this case we have found the program in this directory and do not need to dig any further unless we were installing under some type of special circumstances. Since I am guessing most users reading this guide are mainly looking for how to create their SATA floppy disk we won’t get sidetracked with the other options available in this folder.

Using the MakeDisk.exe Program:

Now that we have found our “MakeDisk.exe” utility you want to double click the file and run the program. When you start the program a Window will open up that says “ASUS File Image Extractor”. “Specify the floppy drive and insert a blank 3.5″, 1.44MB floppy disk”

There is really only one option to specify here and that is the letter of your floppy drive. In most cases it should be defaulted to A: and you should not need to change the selection. If it is set to anything else then you can specify the correct drive letter from the drop down menu. The other section is “Volume” which will most likely be grayed out since the program should be able to auto detect what type of disk you are trying to use.

Once you have confirmed that the correct drive is selected go ahead and click the “Extract” button at the bottom of the program window.

Once you click Extract you will see a progress bar come up that says “Track xx / 160 (50%)“. This will show you once the program has completed creating your driver disk. Once it is complete it will just go back to the main window at which point you should check your A: drive to make sure the disk has been created successfully.

Go ahead and close down the program and then select your A: drive through Windows Explorer. Once you have it selected you should see several files on the disk. Example:

  1. si3114r5.cat

  2. Si3114r5.inf

  3. Si3114r5.sys

  4. SilSupp.cpl

  5. SIPPD.inf

  6. SIWinAcc.sys

  7. TxtSetup.oem

The files may vary a little for your disk but it should pretty much look the same. Just seeing files on the disk should be an indication that the extraction process worked correctly.

At this point you should have a working SATA drivers disk. From this point you can move to the second portion of our guide that will walk you through how to use your SATA drivers disk during the Windows installation process.

How to Find the MakeDisk Program. [Method #2]

If you are unable to manually locate the MakeDisk.exe utility you have one other option available to you. You can do a “Search” through Windows Explorer on your CD to try and find the location of the program.

In Windows Explorer you will want to “right” click on your CD-ROM drive and it should bring up a menu. Select the search option from the menu and it will open a new window that says “Search Results” in the top left hand corner. In the “Search for files or folders named” section type in the following file name:

MakeDisk.exe

Once you click the “Search Now” button the Window should return at least 1 result. In most cases it will return multiple files since there is usually more than one version of the program located on the motherboard disk.

To find the correct version of the program make sure to check the description under the “In Folder” column of the search window. For my example board [A8N-SLI] when I do a search for the program it returns numerous results. Some of the files are located in folders named “SATARAID” or something similar with the term “RAID” in the title. We do not need to worry about those versions of the program unless we are installing our SATA drives in a RAID setup.

As mentioned before you see a folder similar to “SII3114“. Hopefully your search returned a path similar to that to the right hand column of the MakeDisk.exe file your search found. If so that is the one you will want to go with.

Now that you have found the utility you can use it to create your SATA drivers disk. If you have any questions about how to use the program please refer to the section above for detailed instructions.

This concludes how to create your SATA drivers disk for motherboards using an nVidia chipset. From this point on you can refer to the second part of the guide that will walk you through how to perform the Windows installation with your SATA drivers disk.

[NOTE: In the above example we used an A8N-SLI motherboard. I believe this board does not actually require SATA drivers as the board auto detects SATA drives once they are hooked up to it. The above board was for example purposes only so users understand how the SATA driver disk creation works.]

VIA CHIPSET INSTRUCTIONS

Setting up a SATA driver disk for a board that has a VIA chipset can be very different from the method mentioned above.

The first thing you will need to do is put the motherboard CD that came with your mainboard into your system. Once that is done open up Windows Explorer.

Once you have Windows Explorer up, open your CD-ROM drive to explore the contents of the disk. For my example I will be using a BIOSTAR K8VGAM.

When I open the disk I see a series of folders. They are as follows:

  1. AMD_CPU_K8

  2. AUDIO

  3. CHIPSET

  4. ICCARD

  5. LAN

  6. MODEM

  7. SERATA

In this case we will want to go into the “SERATA” folder. Once I have opened this folder I see another folder named “VT6420“.

Since it is the only folder located inside the first folder we will open up this folder next.

Inside this folder you will see quite a few files and folders. The folders listed are as follows:

  1. DRIVERDISK

  2. MASSTOOL

  3. PIDE

  4. RAIDTOOL

  5. VIARAID

In this case go into the “DRIVERDISK” folder to get the files we need to create our SATA drivers disk. As mentioned before setting up the SATA driver disk for a VIA chipset is a very different process then setting up for the nVidia chipset. Here is where the biggest difference comes into effect.

In the DRIVERDISK folder you will most likely see 2 folders and a file. They are named:

  1. PIDE [folder]
  2. RAID [folder]
  3. TXTSETUP.OEM [file]

To create your disk you will want to copy the above files to your floppy disk. Highlight everything in the DRIVERDISK folder [both folders and the file mentioned above] then “right” click and select the “COPY” option from the popup menu. Once you have copied the files, go to your floppy disk in your A: drive and select “EDIT>PASTE“. The files should now be copied over to your floppy disk.

Congratulations. You have now created your SATA Drivers Disk for motherboards with VIA Chipsets. You can now refer to the second portion of our guide for how to use the Drivers Disk during the Windows installation process.

How To Use Your SATA Drivers Disk During the Windows Installation:

01. Confirm the computer is powered off.

Since we are going to be adding new hardware to the system make sure your computer is powered off, with the AC power cable disconnected from the system to prevent and possible hardware damage or injury while working inside the case.

02. Mount the Serial ATA hard drive.

Select an open drive bay within the system and mount you new hard drive into the case. Make sure you have it in an ideal spot so that both the power cables and data cables can reach the drive without a problem.

03. Connect the cables.

Connect the data cable to the drive first. Make sure it feels like it is a snug fit to avoid the chance of the cable falling out if the system is bumped or moved. Then connect the power cable. Depending on the drive and connection it may either be a flat black connection about 1.5 inches wide, or the standard 4 pin Molex connection used with normal hard drives.

04. Insert the Windows XP/2000 installation CD.

Since you are going to be installing your operating system on to the new SATA drive make sure your setup disc is in your CD-Rom when you power up the system. You also need to make sure you have a floppy drive installed in the system since you are going to need to load your SATA drivers off a floppy disc before the system will recognize your new hard drive during the install process.

05. Power up the computer.

Once your new hardware is installed and setup in your system. Check any final options you need to have configured. The main one being that “Floppy Seek” is enabled in your BIOS so the system knows to look for a floppy drive. Otherwise it will give you an error like “No Floppy Drive Detected”. When you first boot the computer you will want to make sure your floppy drivers disc is not in your floppy drive since this will interfere with the system booting off the Windows Setup disc. Insert the floppy disc when you see the screen go black right before the installation process. It will display a message that says:

“Setup is Inspecting your Computers Hardware Configuration”

06. Press the F6 key to install drivers as the Windows setup screen launches.

As soon as the system goes to the next part of the installation it will display a blue screen with a message at the bottom that says:

“Press F6 if you need to install a third party SCSI or RAID driver.”

Since the system will take a few minutes loading drivers for the installation I would recommend tapping the F6 key several times when this screen first comes up. This way you can make sure it does not miss the SATA driver prompt screen when it has finished loading all the drivers.

07. Insert the floppy diskette containing the drivers for the Serial ATA controller.

As mentioned above you should already have loaded your floppy disk into the system. If you have not already done this, do so at this time. Once the system has finished loading the drivers needed for the installation it will prompt you to select you drivers off of the floppy disk. Select which ever drivers pertain to the version of Windows you are using.

[Follow the prompt within this window and it will direct you to your floppy disc and the driver selection screen.]

08. Once the drivers are loaded, proceed with the normal Windows XP/2000 installation.

Once the drivers are loaded the installation will proceed as it would if you were using a normal hard drive. From this point on just act you are installing Windows normally and you should not run into any issues.

You can now easily finish up your install on your system.

Install a New SATA Drive in an Existing Windows System:

This method of installation is easier than the one presented above as it does not require the use of a SATA drivers disc. Since SATA drivers are inherent within the full installation of windows you can use a utility that is provided by the system to setup and configure your new SATA drive. This method assumes your main boot drive is already installed and configured with Windows and you are installing the SATA drive as a secondary storage drive in the system.

  1. Confirm the computer is powered off.
  2. Mount the Serial ATA hard drive.
  3. Connect the cables.
  4. Power up to Windows XP/2000.

Follow the above steps as outlined in part one of this guide. Once you power up the system let it boot into Windows you so can make use of the Disk Management utility.

  1. Insert the CD that contains the drivers for the SATA controller/motherboard.

This step may not be necessary because Windows can usually identify a SATA hard drive after it has been fully installed as mentioned above.

  1. Launch the drivers by double-clicking on them.
  2. The drivers should install themselves.

These two steps may also not be needed since the system should be able to automatically detect your SATA drive through Windows.

  1. Right-click on My Computer.
  2. Select Manage.
  3. Select Disk Management.

The above steps will bring you into the Disk Management utility which you can use to setup and configure your new SATA drive.

  1. Find the SATA hard drive, which should be denoted as “Disk 1″ or similar.
  2. Right-click on the box containing “Disk 1″ or similar.
  3. Choose Initialize or Write Drive Signature (if available).
  4. Right-click on the Unallocated Space to the right of this “Disk 1″ box.
  5. Select New Partition.
  6. Follow the prompts to create and format the partition.

The last few steps will walk you through setting up your new SATA drive for use. Once you have followed through on the prompts you will see a progress screen which will give you an idea of how much time it will take to finish setting up your drive. If you have more questions than what is covered in the above guide please refer to the link below for more information.


See more information on this final process here: http://support.microsoft.com/default.aspx?scid=kb;en-us;309000

More Information on the Installation of Windows


You may never have noticed the “F6″ option before, since it happens at the bottom of the screen and is visible for only a few seconds during a standard install. What you most likely encountered during the setup process was a screen which came up informing you Setup could not find any drives installed on your computer, and it could not continue.

To be able to hit the F6 button, you must restart the Setup process, and watch the bottom of the screen after pressing Enter on the “Welcome to Setup” screen. There will be some moments of files being loaded, and then you should see a message appear which says “Press F6 if you need to install a 3rd party SCSI or RAID driver”. This message will only stay on the screen for a couple of seconds, so press F6 as soon as you see it appear.

After this is done, you will see other messages appear, and it will act as though nothing is happening, but eventually a screen will appear which will allow you to install the drivers for the SATA controller.

After you press “S” on the SATA driver screen, the driver install process will continue and the floppy disk will be needed. Further instructions will be displayed after the driver install process has ended.

From this point on, continue the install like you normally would with Windows since your SATA hard drive should now be recognized by the system and ready for your Windows installation.

Congratulations you have now installed you SATA hard drive into your system. From this point on your computer should treat the drive as a normal hard disk, and you will be able to enjoy all the features of a high speed transfer storage device.



How to Do a Windows Clean Install After a Format

Why do a Clean Install ?

There are many reasons to do a clean install of Windows by formatting your hard drive. It can be good method to follow if you have recently been affected by viruses or spyware. If you have had problems in the past with your current install. Or if you have noticed your system is running slower than it used to and you are trying to increase performance by doing a clean install.

There is also an option in Windows that allows you to do a repair of your operating system, but sometimes this is not offered as an option depending on what version of Windows you are running. Also sometimes the problem may not be fixed by just doing a Windows repair. For example a virus may write itself to other parts of the system, including deep in your registry to avoid this type of recovery. A clean install allows you to rest assured that anything on your system will be completely removed so you do not need to worry about a virus propagating itself.

This guide will be broken into two sections. The first section will walk you through how to do a Format through DOS using a boot disk. [The old school way] The second section of the guide will walk you through doing a Format & Clean Install from your Windows Setup disc. [The easier, preferred method.] If you are just looking for a quick easy way to Format your hard drive and you have your original Windows installation disk handy, I would recommend skipping ahead to the second part of this guide for the “preferred method” of how to Format your drive.

Section #1 – Formatting with a Boot Disk

Section #2 – Formatting with the Windows Setup Disk

How do I do an Old School Format on my Hard Drive ?

There are several methods of how to do this but we are only going to cover the most popular way to perform this procedure. This method is solely for wiping all the information on the drive. After that you would need your Windows Setup Disk to perform the installation of your operating system.

To start you will need a boot disc for Windows. Since most people do not collect system discs we are going to point you towards an online resource that will help you set this up. There is a good site, where you can download the program you need. It can be found at the following link:

http://www.bootdisk.com/

When you get to their main page you will see a link at the top that says:

DOS/Windows9X/Me/NT/2K/XP Excellent Bootdisks

Click on this link and it will take you to a page that has Windows 98′ and DOS boot disks. I would recommend the Windows 98′ OEM link which is the first link in the Windows 98 downloads.

When you click on the link it will open the save file dialog. I would recommend saving this file to your desktop so it is easy to find. Once the file has been saved go to your desktop and you should now see a new file called “boot98.exe”.

Double click the boot98.exe file and a “Batch Assistant” window will open up. The message will tell you to “Insert Floppy to Write”. Make sure you have a floppy disc that does not have important data on it, so you create you Windows 98 boot disk. I recommend formatting the disc, prior to trying to create it so that you will not run into any problems during the creation process.

You can format the floppy disc [click for more info] by clicking on “My Computer” and then right clicking on your “A:\” drive and selecting the format option from the menu. Make sure the drive you have selected is in fact your floppy drive to avoid wiping out data on any of your hard drives.

Once the format dialog is open, go with the default options and just double check to make sure the “file system” is set to “FAT” since we are working with a Windows 98′ disc making utility. Also make sure the option for “quick format” is unchecked so the system will do a more thorough job of wiping all data off the disc. Once you have checked these two options hit the “Start” option and wait for the progress bar to reach 100%. Once it is complete close out of the format dialog.

Once you have your disk clean go back to the batch assistant window and click the “OK” option to create your Windows 98′ boot disk. Once it is done writing the disc close down the program, and check you’re A:\ drive through “My Computer” to make sure you see data on your floppy disc.

You have now created a Windows 98′ boot disc that you can use to format all the data on your hard drive. At this point you would want to insert the disk into the system you want to wipe all the data off of, and then reboot that system with the disk in the drive.

Using Your Boot Disc to Format Your Computer:

When the system reboots with the disc in the floppy drive it will come up with a message:

“Searching for Boot Record from Floppy”

[Make sure your BOOT ORDER is set correctly so the system reads the disc]

Once it finds the disc and reads the information, it will come up with a message that says “Starting Windows ’98″

Once it has finished loading into the boot it will give you a prompt of two or three choices and you will want to select “Start computer without CD-ROM support”. We do not need CD-ROM support in this case because we are only focused on formatting the hard drive right now.

Once you make your selection it will come up to a prompt that says “Preparing to start your computer”. As the message indicates this may take a few minutes so please wait. Once it is done loading it will bring you up to a command prompt that looks like this:

A:\>

From this point you will need to type in the format command, which is as follows:

A:\> FORMAT C:

Once you type this command in you will receive a system message that says:

WARNING, ALL DATA ON NON-REMOVABLE DISK DRIVE C: WILL BE LOST!

Proceed with Format (Y/N)?

Hit “Y” to proceed with the format. As the message above states make sure you have any data you need on the drive backed up prior to attempting the format. If you are ready to proceed hit ENTER after you have typed “Y”.

You will now see another screen with a progress message that says:

Formatting 6,142m

xx% complete

This message shows you the size of the drive you are formatting and the percent complete the operation is at. Once the operation reaches 100% it will go back to the A: prompt:

A:\>

FDISK a Hard Drive:

At this point you can take it one step further if you like and do an FDISK on the hard drive. You don’t really need to do this but some people like to take this extra step to feel like they are working with a nice crisp drive when everything is complete. The FDISK portion of the process is not required when you do a clean format although some people have asked me how to do this so I am including it into the guide.

[NOTE: This part is also covered in an updated method, in the second portion of the guide. This is mainly a continuation of the boot disk method for doing an FDISK on your drive. The section that covers doing this from your original installation disk uses an easier, preferred method for performing an FDISK on your hard drive.]

Follow the steps below to perform an FDISK on your hard drive from the utilities that are included with the boot disk we created.

From the A: prompt type the FDISK command:

A:\> FDISK

It will bring you to a prompt that displays the following message:

“Do you wish to enable large disc support (Y/N)?”

Once again type “Y” for yes, and hit the ENTER key.

It will then ask you:

“Should NTFS partitions on the drives be treated as large (Y/N)?”

Once again type “Y” for yes, and hit the ENTER key.

[This way if you are working with Windows 2000 or Windows XP you will make full use of the entire size of your hard drive.]

At this point it will take you to a menu that offers you several options for operations you can perform. You will want to select option #4 which is “Display Partition Information”

It should show you information that is similar to the following:

Partition                      Type                Volume Label                 Mbytes

1                             NTFS                    primary                            2996

2                           EXT DOS                    n/a                                3153

[In this case the “Volume Label” part has been filled in by me. Not everyone has a drive label assigned, so if you do not this section will probably be blank. The volume label is mainly a name given to the drive that helps you identify it easily. If there is no drive label the n/a would actually just be blank.]

Once you have checked out the drive information you should have a better idea of the “TYPE” of drive you are working with. This way when you try to delete the partition, you know what option you will need to select from the main menu.

Hit “ESC” to go back to the main menu, and then select the option that says:

“Delete partition or logical drive”

It will take you to another menu where you can choose the following option:

#3 Delete Logical DOS Drive in the extended DOS partition

#4 Delete Non-DOS Partition

Depending on the “TYPE” of drive you have you will want to pick one of those options to delete the partition. If you are unsure just pick one and see if the next screen displays drive information. If it does not hit “ESC” go back to the main menu and select “Delete partition or logical drive” again, and then try choosing the other option.

Once you are at the correct screen you will also notice a message that says:

WARNING – Data in the deleted Non-DOS partition will be lost.

Since we formatted the drive earlier we do not need to worry about this part.

It will also have a prompt that asks you:

“What Non-DOS partition do you want to delete?”

At this point you need to “Select Drive #” and it will ask if you wish to continue. Type “Y” for yes.

You may also be asked to select by “Drive Letter”, and then “Enter Volume Label” and it will then ask “Are You Sure (Y/N)” Type “Y” for this also.

[The steps above may vary since people have different drive letters and labels but because we are at a point where there is no data on the drive you don't need to worry about working through trial and error to delete the partition. Even people who are familiar with the process need to do that at times, since a drive may be setup differently than what they are used to, especially when troubleshooting. Just be patient and you will eventually be able to delete your current partition.]

Once you have deleted the partition you will see your drive information disappear and you can now hit “ESC” to go back to the main menu and recreate your partition.

Recreating a partition is much easier than deleting it since it’s pretty much a two step process, and usually goes the same way each time.

From the main menu select option #1:

“Create DOS partition or logical DOS drive”

Once you have selected that, you be prompted for one more option and you should select:

“Create primary DOS partition”

Once you have made you choice you will see a message on the screen that says:

“Verifying Drive Integrity %”

This will show you the overall progress of the operation and once it is complete it will display a message that says:

“Do you wish to use the maximum available size for a primary DOS partition and make the partition active? (Y/N)”

Select “Y” for yes and you should see the message:

“Verifying Drive Integrity %”

Once this operation is complete you should see a message that says:

“You must restart for changes to take effect”

You have now run through a basic crash course on how to FDISK a drive from a boot disk. This step is not crucial to do when formatting a hard drive but since I have been asked about this so many times I wanted to include some basic information on the procedure for those who have never done it before.

How do I do a Clean Format and Install through Windows Setup ?

It used to be that back in the day you needed to do a Format by running utilities through DOS. Because this was such a round about way to do such a simple task Microsoft finally included a utility right through the setup screen to make this process easier.

If you do not want to mess around with creating boot disks or working through a DOS prompt to format your drive this is the method you will want to follow.

Make sure your “BOOT ORDER” is setup correctly so that your CD-ROM will boot before your hard drive and insert your Windows installation disk into the system. Reset your computer and when it boots it should give you a prompt that says:

“Hit any key to boot from CD..”

You need to hit a key as soon as you see this message since it is only displayed for about 3 seconds before your system skips the CD-ROM. If you miss this prompt then reset the system and make sure you hit the key the next time the message is displayed.

Once you hit any key you should see a message on a black screen that says:

“Setup is inspecting your computers hardware configuration”

Once it is complete it will take you to a blue setup screen that says “Windows Setup” in the top left hand corner and should also display a message that says “Setup is loading files” at the bottom of the screen.

This may take a few minutes depending on how fast your system is, and once it gets past this point it will take you to a screen that has three options on it. You will want to pick the first option that says:

“To setup Windows XP now, press ENTER”

Go ahead and hit ENTER at this point to begin the setup process. You should see a message that says “Please wait” and once it loads into the next screen it will show you the Windows License Agreement. You will want to hit F8 on this screen to agree to the license and progress in the setup process.

F8 = I agree

It will show you the “loading” message again and then take you to a screen that has two options on it. You will want to select the option that says:

“To continue installing a fresh copy of Windows XP without repairing, press ESC”

ESC = Don’t Repair

The next page will show you partition information for the hard drive. This is the section I mentioned before that will take you through a simplified FDISK procedure for the system. Since you are following this guide to do a Format on your hard drive lets go ahead and delete the current partition to do the first step in wiping your data off this drive.

On the Delete Partitions screen go ahead and hit the “D” key to delete the current partition.

D = Delete Partition

It will bring up a message that says:

“To delete this partition press ENTER. Setup will prompt you for confirmation before deleting the partition”.

ENTER = Continue

Go ahead and press ENTER to continue the delete partition process. Once you hit ENTER it will take you to a confirmation screen that says:

“You asked setup to delete the partition” and will show you data on your drive:

C: Partition [NTFS]               76309 MB (75120 MB FREE)

“To delete this partition press L.

CAUTION: All data on this partition will be lost”.

L = DELETE

Go ahead and hit “L” to confirm that you want to delete the partition, and once you do this it will take you back to the main page.

It should now show you drive information that will look like this:

Unpartitioned Space            76517 MB

At this point you have deleted the partition on your hard drive and completed the first step in wiping off your data. From this point you will want to create a new partition and then the setup program will Format your new partition.

To create a new partition you will want to hit “C”

C = Create Partition

It will take you to a screen that has the following message:

“To create the new partition enter a size below and press enter”

[I would recommend going with the default size that the system enters automatically. You do not need to change this option unless you are creating Multiple Partitions which we will cover in another guide.]

ENTER = Create

Go ahead and press ENTER and the setup program will create a new partition and then take you back to the main page.

You should now see that there has been a new partition created on hard drive and the setup program will now give you an option at the bottom of the screen that says:

ENTER = Install

Hit ENTER and it will take you to another screen that says:

Format the partition using the NTFS file system (Quick)

Format the partition using the NTFS file system

I would recommend using the “Quick” option because it will take less time and get you to the reinstall portion of setup much faster. Since you already had data on the drive at one point you are able to use the quick option since the standard option is usually only used the first time a hard drive is setup and takes MUCH longer.

[NOTE: One thing to remember is that the standard format option is used when the drive is first setup. The main advantage is that it does a basic error check for any bad sectors on your drive, and is a little more thorough than the quick option. Both options will remove all data from your drive.]

Once you have highlighted the Format “Quick” option hit ENTER to continue with setup:

ENTER = Continue

You have now successfully preformed FDISK and FORMAT through the Windows Installation Disk. From this point on the installation will be the standard Windows install. Just follow the prompts and provide the necessary information [i.e. Windows Key, Date, Time, Time zone, Network Info, Computer Name, etc.] The installation Wizard will walk you through the rest of the setup process and you can reinstall your operating system knowing that you have a fresh clean hard drive to work with.

At this point hopefully any virus, spyware or corruption problems will be fixed and you should have no more issues. If you do experience any other problems after doing the clean install you may be running into some type of hardware issue with the hard drive itself and may want to look into contacting the manufacturer to find out about warranty info on the drive or doing an RMA [Return to Manufacturer] for replacement.

Good luck with your install, and enjoy your clean crisp hard drive and improved performance now that you are starting over on a clean slate.




You can follow any responses to this entry through the RSS 2.0 feed. You can leave a response, or trackback from your own site.